Monday, July 4, 2016

Having a go at some timber in-lay

My girlfriend and I decided we needed a shoe chest for the end of our bed.  So we draw something up and had a go.

Was pretty happy with the end result.

Engraving Carbon Fibre

I decided I needed a new, unique name plate for my desk at work.

I practiced on some aluminium first and was very happy with the clarity of the engraving.

I then needed to machine a nice and level base for the panel.  As any deviation in the surface directly effects the quality of the engraving.  The carbon fibre is some cheap cosmetic panels about 2mm thick from ebay.
The cutter is 60° included angle single flute, solid carbide.  The tip width is about 0.5mm.  Spindle speed was 24,000 RPM with a feed rate of about 600mm/min.  The trimming was done with a 1/8" carbide grouter remover bit from dremel.  (carbide grit burr)


New VFD enclosure, how does it go with aluminium?

Trial cuts on some aluminium off cuts seemed pretty good.



The panels cut well with a 3.2mm cutter at 18000 RPM with a feed rate of about 2000mm/min.  The depth of cut was limited to about 0.5mm as the machine isn't terribly stiff at the moment.



The 200 odd 2mm holes drilled extremely well.  One drill bit lasted the whole run.  Turns out the correct speeds and feeds make a huge difference.

Its new VFD time!

Since our first Huanyang VFD (variable frequency drive) packed it in, we had been running our 300W Ryobi trimming router. 

So we finally got our act together an ordered a new OMORN VFD.  The first cutting job was some 3D profiling of MDF to make my first CNC routed mould for composite parts.



Hacking into the chuck of MDF router a 6mm single flute end mill.  Followed by an 6mm ball mill for shaping,



Surface finish in the MDF after the first past at 0° the second image shows the finish after a pass at 45°


The MDF was treated with 3 coats of epoxy.  Then sanded back to a surprisingly smooth surface finish.  I was very happy with the quality of the mould surface.


Carbon fibre component being vacuum bagged.


Component released from the mould.


I then packed the part up in the mould by 3mm and ran a trace program with a 3.2mm carbide burr to cut out the part.


This finished part is a gooseneck fitting with mounts for lower stays on the one bracket.  This will be used on the sailing boat I built several years ago.

Making a Fishing Rod Lathe

My cousin is a mad keen fisherman and this is something that we had talked about around the table at family gatherings.  The concept of a fishing rod lathe. 
This is a piece of equipment that is used to rotate a fishing rod blank or a damaged rod to fit the fairleads or eyes on the fishing rod.  The eyes are held on by a whipping then coated in resin.  Ideally the lathe is left spinning while the resin dries to ensure and even and drip free finish.

My design was based around a plywood structure and some cheap components from eBay. 

The chuck, spindle and motor block.

The chuck utilises Tee nuts to secure the chuck jaws.  I had looked at 3D printing a complete 3-jaw scroll chuck, like a typical metal lathe.  But deemed this simple CNC router cut idea to do the job in the time frame.

The shaft is an M12 x 200 hex head bolt.  The hex is bonded into the chuck with "knead it" quick putty from Bunnings.  (The "knead it - steel" is very handy to have laying around).

The spindle runs in deep groove ball bearings which are counter bored into the upright pieces.  The motor is a 60 RPM motor from ebay for about $10.  Then a simple PWM DC motor controller from ebay - $10.

The top roller is spring loaded to make it easy to install the rods.  The middle support also can slide to any point on the base plate so you can place the support next to where you are working.

Wednesday, June 29, 2016

More cutting


Using the router to rebate multiple lengths of timber at once.


New shelving for the shed.


Some decorations for a friends wedding.

cutting

Having a go at 3D profiling.

Roughing pass on polystyrene foam for part of a rudder mould.

Finishing pass

.
Finished profile.

Motors are stable at 60°C


Another crash.  At least we know we can cut at full depth and rapid speeds.

Cutting some panels.